BOX 25 - Kits 97-98-99-100

Kit 97

Parts of number 97

  • 97A Rocker panel, right
  • 97B Upper support
  • 97C Bracket #1 (x 2)
  • 97D Bracket #2
  • 97E Bracket #3
  • 97F Front panel
  • Screw IM M 1.7 x 3.5 mm (x 14)
  • Screw SM M 1.7 x 3.5 mm  (x 3)
Assembly and fitting of the right side rocker panel

Step 1

Place the brackets (97D#2 & 96E#3) and brackets (97C#1) on the right rocker panel (97A) and secure these with four IM screws. Place the upper support (97B) and the front panel (97F) onto to the right rocker panel (97A) and secure these with 3 IM screws.

Step 2

Position the right rocker panel (97A) onto the attachment points of the lower frame (25A) and right side platform (73A) and secure with four IM screws (see opposite and below).

Step 3

Open the right door and attach the right rocker panel (97A) – with the help of the upper support (97B) – onto the chassis (34B) with an IM screw, through the opening in the back of the right cockpit housing (68B). Replace the two IM screws with the new provided SM screws.

ASSEMBLY DIAGRAM
GENERAL VIEW

Kit 98

Parts of number 98

  • 98A Left trim panel
  • 98B Right trim panel
  • 98C Left trim strip
  • 98D Right trim strip

Attaching trim panels and trim strips to the cockpit

Step 1

Open the right door and secure the right trim panel (98B) with its four lugs to the right cockpit housing (68B).

Attach the right trim strip (98D) along the edge of the right trim panel (98B) to the right cockpit housing (68B).

Step 2

With the right trim strip (98D) and right trim panel (98B) fitted, now close the right door. Open the left door and fit the left trim panel (98A) by sliding it under the ignition box (56L) - green arrow - then over the left cockpit housing (68A) - blue arrow.

Step 3

Fit the left trim strip (98C) along the edge of the left trim panel (98A) to the left cockpit housing (68A). With the left trim strip (98C) and left trim panel (98A) attached, proceed to close the left door.

ASSEMBLY DIAGRAM
GENERAL VIEW

Kit 99

Parts of number 99

  • 99A Flat floor panel
  • 99B Fixing bracket
  • 99C Decal (x 2)
  • Screw BM M 2.0 x 4 mm (x 8)
  • Screw PM M 2.0 x 4 mm (x 6)
  • Screw MP M 2.0 x 4 mm (x 3)
  • Screw OP M 1.7 x 3 mm (x 3)

Assembly of switch, loudspeaker and flat floor panel

Step 1

Position the loudspeaker (34C) in the round recess provided in the flat floor panel (99A), and secure it with the mounting bracket (99B) and two MP screws - see illustrations above.

Step 2

Position the flat floor panel (99A) against the bottom of the upside-down car and secure the switch (33D) with two OP screws.

Step 3

Connect the yellow speaker cable (34C) to the yellow cable of the PCB (32D). Turn the flat floor panel (99A) upside down.

Step 4

The previously connected cables are now hidden underneath the flat floor panel (99A). Align the flat floor panel (99A) with the bottom of the car and secure it to the lower frame (25A) using five PM screws.

Step 5

Secure the left and right sides of the flat floor panel (99A) to the undercarriage (25A) using six BM screws.

Step 6

Immerse the decal (99C) in water for 30 seconds, then slide it from its paper backing and position it in the middle of the rear bonnet panel (93A).

Step 7

Position the rear bonnet (90A) onto the body (80A) at a 45 degree angle (red arrow), then close the bonnet (blue arrow). Take care not to scratch the edge of the bodywork when closing the bonnet (green arrow).

Step 8

Raise the rear bonnet (90A), then extend the support arm (46J-46K) and check that it is supporting the bonnet correctly. If necessary, slightly loosen the two hinge screws (red arrows) until the arm is aligned with the support point on the bonnet.

ASSEMBLY DIAGRAM
GENERAL VIEW

Kit 100

Parts of number 100

  • 100A Battery compartment cover
  • 100B Decal emblem (x 2)
  • 100C Decal door number (x 4)
  • 100D Decal rear bonnet number (x 2)

Position of Porsche emblem and race number decals on the sides and top of the rear bonnet

Step 1

Immerse the emblem decal (100B) in water for 30 seconds to soften it. Position the decal (100B) on the bumper at the front of the body (80A), then carefully slide it off its paper backing. While it is still wet, you are able to adjust the decal (100B), if necessary.

Step 2

Immerse the door number decal (100C) in water for 30 seconds to soften it. Position the decal (100C) so that it is in line with the racing number on the left-hand lower door, then carefully slide it from its paper backing. Adjust the decal (100C) while it is still slightly wet and remove any excess water with a soft cotton pad.

Step 3

Immerse the door number decal (100C) in water for 30 seconds to soften it. Position the decal (100C) so that it is in line with the racing number on the left-hand lower door, then carefully slide it from its paper backing. Adjust the decal (100C) while it is still slightly wet and remove any excess water with a soft cotton pad.

Step 4

Immerse the number decal for the rear bonnet (100D) in water for 30 seconds to soften it. Position the decal (100D) above and to the rear right of the rear bonnet (90A), then carefully slide it from its backing paper. Adjust the decal (100D) while it is still wet and remove any excess water with a soft cotton pad.

Step 5

Position the bonnet (1B) onto the front body compartment (80A) and secure it using six blue bonnet clips (82F), one white bonnet clip (82H) and one orange bonnet clip (82G).

Place two type AAA batteries ( these are not supplied) in the battery compartment and position the cover (100A) in the flat floor panel (99A). Operate the switch (32D) by moving it forwards.

Step 6

Open the left door and press the switch (64L) to check that the lights are working as shown in the following three illustrations.

Rear lights 48D et 49D

Step 7

The four front lights

Dashboard backlights

Step 8

Press the brake pedal (26F) - the one in the middle - by using the tip of a pencil to check that the brake lights (48D & 49D) at the rear are working properly - illustrations above.

Step 9

Press the switch (64M) to activate the horn. Press the switch (64L) to activate the engine running sound.

Step 10

Place two supports (78C) underneath the left and right side of the car to keep the wheels raised and check that the steering wheel rotates correctly.

ASSEMBLY DIAGRAM
GENERAL VIEW