BOX 27 - Kits 105-106-107-108

Kit 105 - LEFT REARVIEW MIRROR

105A Left exterior mirror
105B Mirror joint
105C Mirror support
105D Support rod

105E Rearview mirror
105F Door sill protection
Screw ACP P 1.4 x 3 mm (x 2)
Screw AGM M 2.0 x 3 mm (x 3)

Step 1

Place the mirror (105A), the joint (105B) and the support (105C) on the work surface.

Insert the pin of the joint (105B) into the opening located at the base of the mirror support (105C), as shown in the photos.

Step 2

Position the assembly made in step 1 in the rearview mirror (105A).

Remove the protective film from the double-sided adhesive that is on the mirror (105E), then position the mirror (105E) on the support (105C) by pressing it and ensuring that the shapes match.

Step 3

Place the left exterior mirror (105A) on the left door (103A), then secure it from the inside with an ACP screw.

Step 4

Position the support rod (105D) respecting the direction as indicated in the detail photo. One of the pins to be inserted into the opening provided on the door (103A) and the other into the opening located at the base of the rearview mirror (105A).

Step 5

Position the sill protection (105F) on the base of the door (103A), interior side. Align the two openings of the sill protection (105F) with the two supports of the door (103E). Secure the door sill protection (105F) with two AGM screws (yellow circles).

GENERAL VIEW

Kit 106 - LEFT DOOR INTERIOR TRIM #A

106A Left door inner panel #A

Screw AGM M 2.0 x 3 mm (x 4)

Step 1

Position panel #A (106A) on the inside of the left door (103A) as indicated, then secure it with three AGM screws.

GENERAL VIEW

Kit 107 - LEFT DOOR INTERIOR TRIM #B

107A Left door inner panel #B
Screw AP M 1.7 x 4 mm (x 3)

Screw AGM M 2.0 x 3 mm (x 3)
Flat Head Screw AIM M 2.0 x 3 x 6 mm (x 3)

Step 1

Position panel #B (107A) on the inside of the left door (103A) as shown, then secure it with two AIM screws in the two openings marked with a red circle.

Then secure panel #B (107A) on the closing side of the door (103A) with two AP screws (yellow circles).

Step 2

Take the bodywork (93A) assembled during the previous steps.

Open the door hinge (103B) and position the pins opposite the three openings in the bodywork (93A) as indicated (yellow circles).

Close the door and secure it with two AIM screws. Start by lightly tightening the screws, then check alignment and then tighten the screws fully. Check the opening and closing of the door and act on the screws to adjust its positioning as best as possible if necessary.

GENERAL VIEW

Kit 108 - RIGHT DOOR

108A Right Door
108B Door hinge
108C Hinge spring
108D Door handle support

108E Door handle
Screw AP M 1.7 x 4 mm (x 2)
Flat head screw AIM M 2.0 x 3 x 6 mm (x 2)

Step 1

Place the door handle support (108D) with the inside facing up – see picture. Insert the door handle (108E) into the housing, ensuring that the pin is correctly aligned with the opening (yellow circle). The door handle is assembled upside down.

Position the door handle support (108D) on the right door (108A), matching the mounting opening as per picture.

Secure the door handle support (108D) from the inside of the door with one AP screw.

Step 2

Position the door hinge (108B) on the inside of the door (103A). Check the correct orientation of the hinge (108B).

Position the hinge spring (108C) by centering the mounting opening with the seat of the screw (yellow circle) and aligning the rear pin with the rear opening of the spring (blue circle). Secure the hinge spring (108C) with an AIM screw.