BOX 13 - Kits 49-50-51-52

Kit 49 - SPARK PLUG WIRES

Parts of number 049

  • 49A Corrugated hose 
  • 49B Hose support (x 2) 
  • 49C Oil hose fitting 
  • 49D Oil hose 
  • 49E Spark plug wire 
  • 49F Spark plug cap (x 4) 
Step 1
Position the two hose supports (49B) on the right cylinder head cover (30B).

Step 2

Place one end of the corrugated hose (49A) on the oil tank #6 (28F). Pass the hose (49A) through the two support brackets (49B), then connect it to air duct #2 (37H).

Step 3

Place the oil hose fitting (49C) onto the engine cylinder head (30A). Cut two 60mm long sections from the oil hose (49D). Connect the first section to the right engine block (29A) and fitting (49C), then connect the second section to oil filler neck #4 (28D) and fitting (49C).

Step 4

Cut four sections of 30mm, 40mm, 55mm and 65mm long from the spark plug wire (49E). Insert a spark plug cap (49F) into one end of each section. Then connect the four caps (49F) to the engine cylinder head (30A). Connect the remaining free ends of each spark plug wire to the ignition distributor (31J) following the order shown in the photo.

Step 5

Cut a section of  85mm long from the spark plug wire (49E) and connect one end to the ignition coil (28I).

Step 6

Connect the other end of the 85mm long wire to the ignition distributor (31J) as shown in the photo.

GENERAL VIEW

Kit 50 - FUEL SUPPLY HOSES

Parts of number 050

  • 50A Fuel Hose 
  • 50B 4-way attachment (x 2) 
  • 50C 3-way attachment
  • 50D Injectors (x 4) 
  • 50E Elbow fitting (x 2) 
  • 50F Fitting (x 2) 
Step 1

Detach the four injectors (50D) from the sprue and place them on intake manifold #1 (33A).

Step 2

Cut four sections of 60mm, 75mm, 85mm and 95mm long from the fuel hose (50A). Connect one end of each section to an injector (50D) as shown in the photo. Position the attachments (50B&50C) as indicated.

Step 3

Detach the fittings (50E&50F) from the sprue, and position them as shown in the photo. Then connect the four fuel hoses, according to their length, as shown.

GENERAL VIEW

Kit 51 - LEFT BULKHEAD AND MUDGUARD

Parts of number 051

  • 51A Left  bulkhead
  • 51B Left  mudguard
  •  Screw AM M 1.7 x 4 mm (x 5) 
Step 1

Position the bulkhead (51A) on the left side of the engine cradle and secure with two AM screws.

Step 2

Insert two AM screws into the bulkhead (51A) as shown in the photo.

GENERAL VIEW

Kit 52 - LEFT FUEL TANK

Parts of number 052

  • 52A Left fuel tank 
  • 52B Tank support 
  • 52C Left reinforcement bar 
  • 52D Support leg 
  • 52E filler neck 
  • Screw AP P 1.7 x 4 mm (x 8) 
Step 1

Place the filler neck (52E) onto the left fuel tank (52A).

Step 2

Position the tank support (52B) on the left bulkhead (51A) and secure it with two AP screws.

Step 3

Place the left fuel tank (52A) on the support (52B) and secure from below with three AP screws.

Step 4

Position the support leg (52D) on the left bulkhead (51A) to keep the left fuel tank (52A) in position.

Step 5

Position the left reinforcement bar (52C) as shown, then attach its ends to the left bulkhead (51A) and to the tank support (52B).

Step 6

Position the left mudguard (51B) on the left bulkhead (51A) and secure with two AP screws.

Step 7

Connect the fuel hose (28M) to the left fuel tank (52A).

GENERAL VIEW