BOX 19 - Kits 73-74-75-76

Kit 73 - DRIVER SEAT BELTS (2)

Parts of number 073

  • 73A Short/waste seat belt strap (x 2)  
  • 73B Hook (x 2) 
  • 73C Short/waste seat belt attachment hook (x 2) 
  • 73D Belt tensioner (x 5) 
  • 73E Long/body seat belt strap (x 2) 
  • 73F Central locking buckle (x 2) 
  • 73G Double-sided adhesive 
Step 1
Position four pieces of double-sided tape (73G) on the ends/tips of the short front belt straps (73A). Turn the straps over and engage the ends in the belt attachment hooks (73C).

Turn the straps over again (73A). Remove the protective film from the double-sided adhesives (73G) and bend the ends of the straps to hold the attachment hooks.

Step 2

Engage the belt tensioners (73D) on the short seat belt straps (73A).

Turn the straps over (73A). Remove the protective film from the double-sided adhesives (73G) and bend the ends of the straps to hold the belt tensioners.

Step 3

Place four pieces of double-sided adhesive (73G) on the ends/tips of the long seat belt straps (73E).

Turn the straps and engage the ends in the central locking buckles (73F). Turn the straps over again (73E). Remove the protective film from the double-sided adhesives (73G) and bend the ends of the straps to hold the central locking buckles.

Step 4

Engage the other ends of the long seat belt straps (73E) into the belt tensioners (73D) as shown in the picture.

Turn the straps and remove the protective film from the double-sided adhesives (73G), then bend the ends/tips of the straps (73E) to hold them on the belt tensioners (73D).

GENERAL VIEW

Kit 74 - DRIVER SEAT BELTS (3)

Parts of number 074

  • 74A Center seat belt strap (x 2) 
  • 74B Hook (x 2) 
  • 74C Center seat belt attachment hook (x 2) 
  • 74D Central locking buckle 
  • 74E Belt buckle lock control 
  • 74F Belt Buckle Lock 
  • 74G Double-sided adhesive 
Step 1

Cut the ends of the center seat belt straps (74A) as shown in the photo. If necessary, use a lighter to prevent the cut ends from fraying. Place four pieces of double-sided tape (74G) on the ends of the center seat belt straps (74A).

Step 2

Engage the ends of the center seat belt straps (74A) in the central locking buckle (74D). Remove the protective film from the double-sided adhesives (74G), then fold the ends/tips of the straps (74A) to hold them on the central locking buckle.

Step 3

Place the center seat belt attachment hooks (74C) onto the center seat belt straps (74A). Make sure the hooks are correctly aligned. Turn the straps over (74A). Remove the protective film from the double-sided adhesives (74G) and bend the ends/tips of the straps to hold the attachment hooks.

Step 4

Group the central locking buckle (74D) and the two central locking buckles (72G) onto the belt buckle lock (74F).

GENERAL VIEW

Kit 75 - DRIVER’S SEAT

Parts of number 075

  • 75A Driver’s seat 
  • 75B Driver’s seat rear frame 
  • 75C Driver’s seat support (x 2) 
  • Screw AP P 1.7 x 4 mm (x 10) 
  • Screw SP P 1.7 x 3 mm (x 6) 
Step 1

Place the two hooks (74B) on the driver's seat (75A). 

Step 2

Place the driver's seat (75A) on the rear frame (75B) and secure  from behind with four SP screws.

Step 3

Place a seat support (75C) on the left side of the rear frame (75B) and secure with two AP screws. Place the second seat support (75C) on the right side of the rear frame (75B) and fasten it with two AP screws.

Step 4

Insert the long seat belt straps (73E) onto the sides of the driver’s seat (75A). Position the two central locking buckles (73F) on the belt buckle lock (74F). 

Hang the center belt attachment hooks (74C) onto the hooks (74B). Place the belt buckle lock control (74E) on the lock (74F) (check the correct position of the lever) and secure from below with an SP screw.

Step 5

Position the seat on the left flooring (67A) and secure from below with four AP screws.

Vue générale

Kit 76 - NAVIGATOR SEAT BELTS (1)

Parts of number 076

  • 76A Upper seat belt strap (x 2) 
  • 76B Hook (x 2) 7
  • 76C Upper seat belt attachment hook (x 2) 
  • 76D Belt tensioner (x 5) 
  • 76E Buckle (x 2) 
  • 76F Lower Seat Belt strap (x 2) 
  • 76G Central locking buckle (x 2) 
  • 76H Double-sided adhesive 
Step 1

Place four pieces of double-sided tape (76H) on the ends/tips of the upper seat belt straps (76A). The adhesives must be placed on the rear side of the straps (the one where the marking is not visible) Turn the straps over and place the ends in the tensioners (76D). 

Turn the straps over again (76A). Remove the protective film from the double-sided tapes (76H) and bend the ends/tips of the straps to keep the tensioners (76D) in place.

Step 2

Position the buckles (76E) on the upper seat belt straps (76A).

Step 3

Place the attachment hooks (76C) on the upper seat belt straps (76A). Make sure the hooks are correctly aligned. 

Flip the straps (76A). Remove the protective film from the double-sided tapes (76H) and bend the ends/tips of the straps to hold the attachment hooks.

Step 4

Place four pieces of double-sided tape (76H) on the ends/tips of the lower seat belt straps (76F). Turn the straps over and engage the ends/tips in the belt tensioners (76D). 

Remove the protective film from the double-sided tapes (76H) and bend the ends/tips of the lower straps (76F) to keep the tensioners (76D) in place.

Step 5

Position the central locking buckles (76G) on the lower seat belt straps (76F). Remove the protective film from the double-sided tapes (76H) and bend the ends/tips of the straps to fix them to the central locking buckles (76G).

GENERAL VIEW