BOX 8 - Kits 29-30-31-32

Kit 29 - EXHAUST MANIFOLDS

Parts of number 029

  • 29A Right engine block 
  • 29B Exhaust Manifold #1 
  • 29C Exhaust Manifold #2 
  • 29D Exhaust Manifold #3 
  • 29E Exhaust Manifold #4 
  • Screw AP P 1.7 x 4 mm (x 9) 
Step 1
Place exhaust manifold #1 (29B) onto exhaust manifold #2 (29C). Attach them together with an AP screw.

Step 2

Place exhaust manifold #3 (29D) onto exhaust manifold #2 (29C). Secure manifold #3 (29D) with AP screw.

Step 3

Place exhaust manifold #4 (29E) onto exhaust manifold #1 (29B). Secure manifold #4 (29E) with AP screw.

Step 4

Place the assembly of the four exhaust manifolds on the right engine block (29A). Secure each manifold to the engine block with a screw from below.

GENERAL VIEW

Kit 30 - ENGINE CYLINDER HEAD AND CYLINDER HEAD COVER

Parts of number 030

  • 30A Engine cylinder head 
  • 30B Right cylinder head cover 
  • 30C Left cylinder head cover 
  • 30D Connection part
  • Screw AM M 1.7 x 4 mm (x 5) 
  • Screw UM M 1.7 x 3 mm (x 5 )
Step 1

Position the connection part (30D) on the engine cylinder head (30A). Secure the connection part (30D) with two AM screws.

Step 2

Position the right cylinder head cover (30B) on the engine cylinder head (30A) and secure with two UM screws. Position the left cylinder head cover (30C) on the engine cylinder head (30A) and secure with two UM screws.

Step 3

Position the assembled cylinder head on the right engine block (29A). Secure the connection part (30D) to the right engine block with two AM screws.

GENERAL VIEW

Kit 31 - OIL SUMP AND OIL PUMP

Parts of number 031

  • 31A Gearbox housing 
  • 31B Oil sump 
  • 31C Oil sump seal
  • 31D Oil pump 
  • 31E Oil line #1 
  • 31F Oil line #2 
  • 31G Oil pump cover 
  • 31H Oil line #3 
  • 31I Engine front seal 
  • 31J Ignition distributor 
  • Screw AM M 1.7 x 4 mm (x 4) 
  • Screw CM M 2.0 x 4 mm (x 10) 
  • Screw AP P 1.7 x 4 mm (x 2) 
Step 1

Cut two sections of 130 mm and 80 mm long from oil line #3 (31H). Connect the 130 mm section (long) to oil tank #1 (28A) and the 80 mm section (short) to oil tank #7 (28G).

Step 2

Position the front engine seal (31I) on the right engine block (29A) and secure with an AM screw.

Step 3

Position the ignition distributor (31J) on the right engine block (29A) and secure with an AP screw. 

Step 4

Position the oil sump seal (31C) on the oil sump (31B) and secure with two CM screws.

Step 5

Position the gearbox housing (31A) on the right engine block (29A) and secure it from behind with four CM screws. 

Step 6

Position the oil sump (31B) below the right engine block (29A) and secure with two CM screws on the seal (31C).

Step 7

Position the oil pump (31D) on the oil sump (31B), then secure it with two AM screws. Position the oil pump cover (31G) on the oil pump (31D) as shown in the photo.

Step 8

Position oil lines #1 (31E) and #2 (31F) onto oil pump (31G).

GENERAL VIEW

Kit 32 - LEFT ENGINE BLOCK

Parts of number 032

  • 32A Left engine block 
  • 32B Oil filter #1 
  • 32C Oil filter #2 
  • 32D Starter motor #1 
  • 32E Starter motor #2 
  • Screw AP P 1.7 x 4 mm (x 2) 
Step 1

Assemble the two starter parts (32D&32E). 

Step 2

Assemble the two oil filter parts (32B&32C).

Step 3

Place the oil filter on the left engine block (32A) and secure from below with an AP screw. Carefully set the starter aside for later use. 

GENERAL VIEW