BOX 19 - Kits 73-74-75-76

Kit 73 - Installation of ventilation vents and grills

Parts of number 73

  • 73A Left ventilation vent 
  • 73B Right ventilation vent 
  • 73C Left ventilation grill 
  • 73D Right ventilation grill 
  • Screw MM M 1.2 x 3 mm (x 10) 
  • Screw AP M 1.7 x 4 mm (x 4)
Step 1
Position the right ventilation grill (73D) on the rear of the bodywork (66A) and secure it from below with an AP screw (illustrations opposite and below).

Step 2

Place the left ventilation grill (73C) on the rear of the bodywork (66A) and secure it from below with two AP screws (illustrations opposite and below).

Step 3

Place the left ventilation vent (73A) on the bodywork (66A) and secure with four MM screws. 

Step 4

Place the right ventilation vent (73B) on the bodywork (66A) and secure with four MM screws.

ASSEMBLY DIAGRAM
GENERAL VIEW

Kit 74 - Assembly and installation of the left rear light

Parts of number 74

  • 74A Left rear light 
  • 74B Left rear light bracket 
  • Screw ABP M 1.4 x 3 x 4 mm (x 2) 
Step 1

Engage the red LEDs of cable D (48D) (disconnected in step 4 of components 48) through the openings located on each side of the rear panel of the body (66A). Note that the longest wire is intended for the right side (red arrow).

Step 2

Place the left rear light (74A) on the left rear light bracket (74B).

Step 3

Insert the left LED (shortest wire) of the cable D (48D) into the left rear bracket (74B), then attach the left rear light (74A) and bracket (74B) to the left side of the rear panel of the bodywork (66A) (illustrations opposite and below).

Step 4

Secure - from the inside - the left rear light (74A) to the bodywork (66A) with an ABP screw.

ASSEMBLY DIAGRAM
GENERAL VIEW

Kit 75 - Assembly and installation of the right rear light

Parts of number 75

  • 75A Right rear light 
  • 75B Right rear light bracket
  • Screw ABP M 1.4 x 3 x 4 mm (x 2) 
Step 1

Place the right rear light (75A) on the right rear support (75B).

Step 2

Insert the right LED (longest wire) of the cable D (48D) into the right rear light bracket (75B).

Step 3

Position the right bracket (75B) and the right rear light (75A) on the right side of the rear panel of the bodywork (66A), then secure them from the inside with an ABP screw (illustrations above).

ASSEMBLY DIAGRAM
GENERAL VIEW

Kit 76 - Assembly and installation of the oil radiator fan. Attachment of the rear light cable

Parts of number 76

  • 76A Oil radiator fan housing 
  • 76B Fan propeller 
  • 76C Axis 
  • 76D Adhesive tape (x 3) 
  • Screw UP M 1.7 x 6 mm (x 2) 
  • Screw NP M 1.2 x 4 mm (x 2) 
Step 1

Position the fan propeller (76B) on the axis (76C) and secure with an NP screw.

Step 2

Place the axis (76C) on the oil radiator fan housing bracket (76A).

Step 3

Position the oil radiator fan housing (76A) underneath the bodywork (66A) and secure with a UP screw.

Step 4

Guide the longest wire of cable D (48D) along the inside of the rear panel of the bodywork (66A) and secure it with two adhesive tapes (76D).

ASSEMBLY DIAGRAM
GENERAL VIEW