BOX 17 - Kits 65-66-67-68

Kit 65 - THE TYRE OF THE SECOND REAR WHEEL

Parts of number 065

  • 65A Tyre 
  • 65B Inner wheel rim 
  • Screw BP M 1.7 x 5 mm (x 5) 
Step 1
Immerse the tire (65A) in luke warm water for 30 seconds to soften it. Once out of the water, dry it carefully, especially the interior part.

Step 2

Place the inner wheel rim (65B) in the tyre (65A). Check that the tyre is correctly positioned (without markings).

Turn the tire (65A) over and position the outer wheel rim (64B). Check that the tire is placed on the correct side (with markings). Turn the tire over again and secure the inner and outer rims together with four BP screws.

GENERAL VIEW

Kit 66 - SECOND REAR DISC BRAKE

Parts of number 066

  • 66A Outer brake disc  
  • 66B Inner brake disc  
  • 66C Washer 
  • Screw AM M 1.7 x 4 mm (x 5) 
  • Screw VM M 3.0 x 4 mm (x 2) 
  • Screw ACP P 1.4 x 3 mm (x 4) 
Step 1

Place the outer brake disc (66A) on the inner brake disc (66B) and secure with three ACP screws.

Step 2

Position the brake caliper (46B) on the right rear hub (46A) and secure it with two AM screws. Position the brake disc on the right rear hub (46A).

Step 3

Place the second brake caliper (46B) on the right rear hub (46A). Insert an AM screw through the brake disc and screw it into one of the two mounting points of the caliper (46B). 

Rotate the brake disc until you find the other caliper mounting point, then insert another AM screw to secure the caliper (46B) to the right rear hub (46A).

Step 4

Place the rear wheel on the right rear hub (46A).

Position washer (66C) into the center of the outer wheel rim (64A). Secure the rear wheel to the right rear hub (46A) with a VM screw.

GENERAL VIEW

Kit 67 - FLOORING

Parts of number 067

  • 67A Left floor panel
  • 67B Right floor panel 
  • 67C Rear joint 
  • 67D Front joint
  • 67E Washer (x 2) 
  • 67F Speaker bracket 
  • 67G Cable Tape 
  • Screw CM M 2.0 x 4 mm (x 7) 
  • Screw SM M 1.7 x 3 mm (x 5) 
  • Screw YM M 1.7 x 4 mm (x 3) 
Step 1

Place the left floor panel (67A) and the right floor panel (67B) side by side and connect them with the rear joint (67C)and secure with two CM screws.

Step 2

Then connect the left (67A) and right (67B) floor panels with the front joint (67D) and secure by two CM screws.

Step 3

Carefully disconnect the speaker (18A), battery compartment (18B), headlight cables (18D), and taillight wire bundle (19A) from the PCB (18C). Position the battery compartment (18B) on the floor and secure with four SM screws.

Step 4

Place the speaker (18A) on the right floor panel (67B) then secure it with the speaker bracket (67F) using two CM screws.

Step 5

Position the PCB (18C) on the left floor panel (67A), then secure it with two YM screws that need to be passed through the two washers (67E).

Step 6

Reconnect the cables of the speaker (18A) and battery compartment (18B) to the PCB (18C).

Step 7

Attach three pieces of tape (67G) to the cables as indicated in the picture.

GENERAL VIEW

Kit 68 - FIRE EXTINGUISHERS

Parts of number 068

  • 68A Left plate 
  • 68B Right Plate 
  • 68C Fire extinguisher #1 
  • 68D Fire extinguisher #2 
  • Screw AP P 1.7 x 4 mm (x 6) 
Step 1

Place the left plate (68A) on the left floor panel (67A) and secure it from below with an AP screw.

Step 2

Position the two fire extinguishers (68C&68D) on the right floor panel (67B) as per picture and secure from below with four AP screws.

GENERAL VIEW