BOX 28 - Kits 109-110-111-112

Kit 109 - RIGHT DOOR WINDOW

Parts of number 109

  • 109A Right window 
  • 109B Window deflector
  • 109C Lower window guide 
  • 109D Upper window guide 
  • 109E Slidable ventilation window 
  • 109F Window Latch 
  • Screw MP M 1.2 x 3 mm (x 9) 
  • Screw AGM M 2.0 x 3 mm (x 5) 
Step 1
Position the deflector (109B) on the outside of the window (109A) and secure it with two MP screws as shown.

Step 2

Place the lower window guide (109C) on the inside of the window (109A) ensuring that the groove is facing upwards as per picture. Center the pin located on the right of the window in the opening of the lower window guide as shown (yellow circle). While holding it in position, secure the guide (109C) from the outside of the window (109A) with two MP screws.

Step 3

Position the sliding window (109E) in the groove of the lower window guide (109C) inside the window (109A). Check that the handle is oriented towards the front of the window.

Step 4

Position the upper window guide (109D) on the inside of the window (109A) ensuring that the groove is facing downwards as per picture. Center the pin located on the right of the window into the opening of the upper window guide as shown (yellow circle). While holding the guide and the window in position, secure the guide (109D) from the outside of the window (109A) with two MP screws.

Step 5

Position the latch (109F) into the opening of the handle of the sliding window (109E) and secure with an MP screw. Check that the latch (109F) turns easily and that it locks the sliding window (109E) correctly. If necessary, tighten or loosen the screw for a proper fit.

Step 6

Place the right window (109A) on the inside of the right door (108A), with the deflector facing outwards. Secure the window (109A) to the left door with four AGM screws.

GENERAL VIEW

Kit 110 - RIGHT REARVIEW MIRROR

Parts of number 110

  • 110A Left exterior mirror 
  • 110B Mirror joint 
  • 110C Mirror support 
  • 110D Support rod 
  • 110E Rearview mirror 
  • 110F Door sill protection 
  • Screw ACP P 1.4 x 3 mm (x 2) 
  • Screw AGM M 2.0 x 3 mm (x 3)
Step 1

Place the mirror (110A), the joint (110B) and the support (110C) on the work surface. 

Insert the pin of the joint (110B) into the opening located at the base of the mirror support (110C), as shown in the photos.

Step 2

Position the assembly made in step 1 in the rearview mirror (110A). 

Remove the protective film from the double-sided adhesive that is on the mirror (110E), then position the mirror (110E) on the support (110C) by pressing it and ensuring that the shapes match.

Step 3

Place the right exterior mirror (110A) on the right door (108A), then secure it from the inside with an ACP screw.

Step 4

Position the support rod (110D) respecting the direction as indicated in the detail photo. One of the pins to be inserted into the opening provided on the door (108A) and the other into the opening located at the base of the rearview mirror (110A).

Step 5

Position the sill protection (110F) on the base of the door (108A), interior side. Align the two openings of the sill protection (110F) with the two supports of the door (108A). Secure the door sill protection (110F) with two AGM screws (yellow circles).

GENERAL VIEW

Kit 111 - RIGHT DOOR INNER TRIM #A

Parts of number 111

  • 111A Right door inner panel #A 
  • 111B Number plate 
  • Screw AGM M 2.0 x 3 mm (x 4)
Step 1

Place the number plate (111B) upside down on the work surface. Remove the protective film from the double-sided adhesive tape. Position the number plate (111B) in the upper left inside corner of the right door inner panel #A (111A). Apply slight pressure so that the double-sided adhesive sticks perfectly.

Step 2

Position panel #A (111A) on the inside of the right door (108A) as shown, then secure it with three AGM screws.

GENERAL VIEW

Kit 112 - RIGHT DOOR INNER TRIM #B

Parts of number 112

  • 112A Right door inner panel #B 
  • Screw AP M 1.7 x 4 mm (x 3) 
  • Screw AGM M 2.0 x 3 mm (x 3) 
  • Flat head screw AIM M 2.0 x 3 x 6 mm (x 3)
Step 1

Position panel #B (112A) on the inside of the right door (108A) as shown, then secure it with two AGM screws into the two openings indicated by a red circle.

Then fix panel #B (112A) on the closing side of the door (108A) with two AP screws (yellow circles).

Step 2

Take the bodywork (93A) assembled in the previous steps.

Open the hinge (108B) and position the pins opposite the three openings in the body (93A) as shown (yellow circles).

Close the door and secure it with two AIM screws. Start by lightly tightening the screws, then check the alignment and tighten the screws fully. Check that the door opens and closes, and adjust the screws if necessary.

GENERAL VIEW